Ein Caeles Plattenspieler als Sonderanfertigung fertig gestellt!

English language text follws German text

Diesmal habe ich eine Caeles in Sonderanfertigung aufgebaut:

Der Kunde hat schlicht und einfach nicht den Platz für die doch recht große Ausführung mit dem pneumatisch gelagerten Subchassis. Also musste eine völlig neue Lösung entwickelt werden.

Statt des Subchassis kommt eine Entkopplungsplattform von minus-k

minus-k

Zum Einsatz:

Diese Plattformen sind für optische Instrumente, Mikroskope etc. gedacht, nicht für Plattenspieler.

Die Auflageplatte ist zur Aufstellung eines Laufwerks von Schwingungs- und Resonanzverhalten nicht geeignet. Deswegen wurde in Einzelfertigung eine Sandwich-Platte aufgebaut, die der Dämpfungsstruktur des Originalen Caeles entspricht.

Dadurch mussten auch die Öldämpfer etwas anders ausgeführt werden.

Das System funktioniert aber einwandfrei!

Siehe die zwei kleinen Videos!

 

 

Als Antrieb kommt derselbe Pabst AC Motor zum Einsatz, der auch im TechDas Zero verwendet wird.

Der Kontroller ist eine Eigenentwicklung. Alles lässt sich sowohl vom Bedienpult, wie vom Kontroller steuern. Sämtliche konzeptionellen Grundstrukturen wurden beibehalten.

Die minus-k Plattform hat nur einen recht engen Spielraum für die Nutzlast um richtig zu arbeiten. Außerdem muss sie gleichmäßig belastet werden. Da der Kunde zwei verschiedene Tonarmbasen verwenden möchte, gibt es ein verschiebbares Ausgleichsgewicht. Die bewährte Umlenkrolle hier in der höchsten Ausbaustufe mit Luftlager.

Die beiden Tonarmbasen sind eine komplette Neukonstruktion: Angefangen hat es damit, dass der Kunde den Kuzma Saphire Tonarm verwenden will. Der passt aber nicht auf die Standard Tonarmbasis. Die neu entwickelte Tonarmbasis behält das Grundprinzip bei, dass die Montageplatte für den Tonarm in drei Spikes gelagert wird. Nur statt der ursprünglichen Platte kommt hier eine Konus-Struktur zum Einsatz. Der untere Teil ist hohl und mit einem speziellen Mix aus Materialien gefüllt um optimale Dämpfung zu erzielen. Ist in der Form eine deutliche Verbesserung zur ursprünglichen Tonarmbasis! Das macht auch die Montage des zweiten Tonarms ein 12 Zoll Primary Control FCL einfacher!

 

 Primary Control FCL Tonarm

Der Tonarm gefällt mir übrigens sehr gut!

 

Das wechseln der Tonarmbasis ist sehr einfach: Die drei unteren Inbusschrauben lösen. Tonarmbasis mir Arm zur Seite stellen. Die zweite Tonarmbasis zu den korrespondierenden Markierungen ausrichten und die drei Inbusschrauben anziehen. Sämtliche Einstellungen von Tonarm und System bleiben so erhalten!

Der Caeles ist ja ganz bewusst so gebaut, dass im Betrieb nur eine Tonarmbasis verwendet werden kann. Nur o kann man auftretende Schwingungen und Resonanzen wirklich kontrollieren und gezielt abführen!

Natürlich braucht der Plattenspieler auch einiges an Peripherie:

Da wäre zuerst einmal Netzteil/Controller für den Motor und die Druckluftsteuerung für das Tellerlager und das Luftlager der Umlenkrolle. Man kann das Laufwerk sowohl von diesem Controller, wie auch vom Bedienpult am Plattenspieler bedienen.

Dann gibt es noch eine Vakuum-Pumpe für die Platten Ansaugung.

Einen Kompressor braucht man natürlich auch noch – hier ein Schraubenkompressor mit Lufttrockner. Auf den Kompressor folgt noch ein Zwischentank mit Druckregler und Filtern.

Diese sind in diesem Falle in die Stromaufbereitung integriert.

Passende Tonarm Kabel und das weit kritischere Kabel zwischen Übertrager und Vorstufe habe ich auch dazu gebaut.

Insgesamt ein richtig gutes komplettes System!

Natürlich muss auch alles ordentlich verpackt werden: 4 Peli-Cases mit Schaumstoffeinllage:

Der Kompressor wird separat verpackt:

 

This time I built a custom-made Caeles:

 

The customer simply does not have the space for the rather large version with the pneumatically mounted subchassis. So, a completely new solution had to be developed.

 

Instead of the subchassis, a decoupling platform from minus-k is used. Used:

minus k

These platforms are intended for optical instruments, microscopes, etc., not for record players. The support plate is not suitable for setting up a turntable in terms of vibration and resonance behavior. Therefore, a sandwich plate was built in individual production that corresponds to the damping structure of the original Caeles. This also meant that the oil dampers had to be designed slightly differently.

 

The system works perfectly!

 

See the two short videos!

 

 

The same Pabst AC motor is used as the drive that is also used in the TechDas Zero. The controller is an in-house development. Everything can be controlled from both the control panel and the controller. All basic conceptual structures have been retained. The minus-k platform only has a very small amount of margin for the payload to work properly. It also needs to be evenly loaded. Since the customer wants to use two different tonearm bases, there is a movable balance weight. The tried and tested pulley here in the highest configuration with air bearings.

 

The two tonearm bases are a completely new design: It started with the customer wanting to use the Kuzma Saphire tonearm. But it doesn’t fit on the standard tonearm base. The newly developed tonearm base retains the basic principle that the mounting plate for the tonearm is supported in three spikes. Only instead of the original plate, a cone structure is used here. The lower part is hollow and filled with a special mix of materials to achieve optimal damping. In terms of shape, it is a significant improvement on the original tonearm base! This also makes mounting the second tonearm, a 12-inch Primary Control FCL, easier!

Primary Control FCL tonearm

https://www.primarycontrol.nl/Field_Coil_Loaded_Unipivot_Tonearm.html

I really like the tonearm, by the way!

 

Changing the tonearm base is very easy: Loosen the three lower Allen screws. Put the tonearm base with the arm to the side. Align the second tonearm base with the corresponding markings and tighten the three Allen screws. All settings for the tonearm and system are retained! The Caeles is deliberately built so that only one tonearm base can be used during operation. Only then can you really control and specifically remove any vibrations and resonances that occur!

 

Of course, the record player also needs a number of peripherals:

 

First of all, there is the power supply/controller for the motor and the compressed air control for the platter bearing and the air bearing of the deflection roller. You can operate the drive from this controller as well as from the control panel on the record player.

 

Then there is a vacuum pump for the record suction. Of course, you also need a compressor – here a screw compressor with air dryer.

 

 

 The compressor is followed by an intermediate tank with pressure regulator and filters. In this case these are integrated into the power conditioning.

 

I also built matching tonearm cables and the far more critical cable between the transformer and the preamp.

 

All in all, a really good complete system!

 

Kommentare sind geschlossen.